DENON DJ SC6000 PRIME for VirtualDJ 8.5+ Last Update : July 2020
Switch to Computer mode
When the SC6000 is powered on, it will be set to Standalone/Engine mode. To switch to Computer mode and control VirtualDJ you need to ...
- press on the Computer icon at the SC6000 screen
- or hold down for a second the VIEW button at the center-top panel of the device, select SOURCE, then pres on the Computer icon.
Firmware & DriversFirmware (both Windows and Mac)
: Update the firmware of the unit to the latest available version from https://www.denondj.com/downloadsDrivers : (Windows only)
Download and install the latest Windows drivers from https://www.denondj.com/downloads
. It is strongly advised to install drivers prior plugging the unit to a USB computer port.
No driver is necessary to be installed on Mac OSX computers.Note
For SC6000 Screen to work on Mac computers, the following OS are supported....
- 11.x (running in Rosetta if M1 Chip)
VirtualDJ 8 SetupDownload and install VirtualDJ from http://www.virtualdj.com/download/index.html (in case you have not done already)
Once VirtualDJ is opened, a Login Window will appear. Login with your virtualdj.com account’s credentials.
A Pro Infinity or a Pro Subscription License is required to use the Denon DJ SC6000. Without any of the above Licenses, the controller will operate for 10 minutes each time you restart VirtualDJ.
A detection windows will appear next verifying proper connection.
Click to OK
The unit is now ready
to operate. Note
: The SC6000 doesn't offer a USB Audio Interface (sound card). See Audio Setup Options in VirtualDJ Manual
For further software settings please refer to the User Guide of VirtualDJ 8. http://www.virtualdj.com/manuals/virtualdj8/index.html
SHIFT (SECONDARY) ACTIONS SHIFTPress this button down to access secondary actions as described in the SHIFT ACTION column D LAYERSelect a deck for the unit to control
When a single device is connected or a 2 Decks skin is used , the SC6000 can be assigned to Left (A) or Right (B) Deck
When 2 devices are connected and a 4 Decks skin is used, the Left assigned device will toggle control for Left Decks (Deck A and C) and the Right-assigned device will toggle control for the Right Decks (B and D) 1 PLAYPlay-pause the trackPlay-stutter track2 CUEWhen track is paused, sets a temporary Cue point and previews track while pressed if the Cue is set. Jump and stop to the Cue point when track is playingJumps at the beginning of the track3 BEAT JUMPSeamlessly move track forward/backwards by the same amount of beats as the selected loop size. Fast seek through the track backwards/forward by 4 beats while pressed.4 TRACK SKIPLeft Track Skip : Jump to the beginning of the track. Double-press the same button to load the previous track from the Browser List.
Right Track Skip : Loads the next track from the Browser List 5 CENSOR Plays the track in reverse while pressed. When released, track will continue playing from the position it would have been if never used (CENSOR)Toggle between Reverse and Normal playback 6 LOOP INSets current position as the Start point (Loop In) of a manual loop. When in Loop, sets Jogwheel to Loop In Adjust mode and then use the Jogwheel to fine adjust the position of the Loop In point in time. 7 LOOP OUTSets current position as the End point (Loop Out) of a manual loop. When in Loop, sets Jogwheel to Loop Out Adjust mode and then use the Jogwheel to fine adjust the position of the Loop Out point in time. 8 LOOPHalf/double the size of the Loop in beats. Push to enable an auto-loop of the selected size in beats or push to exit the loop.When in Loop, turn to move the loop backwards/forward by 1 beat 9 JOGTouch sensitive jogwheel to scratch (if Vinyl mode is selected) or pitch bend. Loop In and Loop Out point adjustment (see Loop In/Out controls above)
The LEDs around the jogwheel will get the color of the deck when track is playing out live and will blink when track is near its end. The Wheel Display will show the Album Art of the loaded track and 2 led rings will indicate the needle/rotation position and the slip mode position (when enabled).Fast search through the track.10 SHORTCUTSShow/Hide the Pads-Sampler-Custom buttons panel 11 SOURCEOffers a confirmation panel on the SC6000 screen to switch to Standalone mode 12 VIEWToggles between Normal Deck and Browser+Mini Deck views on the SC6000 screen.
Hold down for more than 1 second to open the SETTINGS view on the SC6000 screen. 13 EJECTUnload Track from Deck. 14 DISPLAYSee Screen for further details 15 BACKSets Browser focus to Folders list. If focus is on Folders, open/close sub-folders 16 FWDCycles focus between available Browser Lists (folders, Songs, Sideview) 17 BROWSEScrolls through Files and Folders in the focused Browser list.
Push to get the Browser view. When in Browser view, pus to load the selected track to the Deck.
Double-fast-push to clone the Track (and its position and playback status) from the other DeckCycle through the available lists of Sideview (Automix, Sidelist, Karaoke, Sampler and Shortcuts).
Push to add the selected track of Songs List to the selected List of Sideview (Automix, Sidelist, Karaoke) 18 WHEEL ADJUSTAdjust how heavy/light the Jogwheel will feel 19 STOP TIMEAdjust the time the track will need to completely stop. Set to Min for instant stop 20 VINYLEnable/disable Vinyl (Scratch) mode 21 SYNCMatch the corresponding Deck's tempo and phase with the opposite Deck's (or the Master Deck’s if using a 4 decks Skin) tempo and phase 22 MASTERManually set this deck as Master Deck. 23 KEYLOCKLock the track's key to its original value regardless the track's Tempo changes.Smoothly reset Track's tempo to its original value 24 PITCHAdjust the track's playback speed (tempo). When pitch fader is at the middle position (track is playing at its original speed), the white center LED will be lit.
When the green-arrow LEDs are lit, the pitch fader has to be moved to the direction the arrows indicate, in order to catch the pitch value of the deck. This is mostly happening when decks are swapped (via the LAYER button) and the pitch value of one deck is different than the other.
Note that this Hardware-takeover is not following the soft-takeover of VirtualDJ, meaning that if SHIFT is pressed, the arrows will not indicate the direction the pitch fader needs to be moved to in order to re-gain pitch control, but the ghost-fader on the GUI will be an aid 25 SLIPEnable/disable Slip mode. When enabled, several actions like scratching, Hotcues, Loops etc will act temporary, and the track will resume playing from the position it would have been if the action was never triggered. 26 PITCH BENDHold down to temporary speed up/slow down the song while pressed. When released, the track playback will return to the speed designated by the Pitch Fader.Select the previous/next available % range of the Pitch Fader 27 PAD MODESSet Pads to a Pads page.
HOTCUE: Hotcues page (1st press), CueLoop page (2nd press)
LOOP : Loop page (1st press), Saved Loops page (2nd press)
ROLL : Loop Roll page (1st press), KeyCue page (2nd press)
SLICER : Slicer page (1st press), Sampler page (2nd press)
See further details in VirtualDJ Manual - Pads 28 PARAMETERAdjust the 1st Parameter of the selected Pads pageAdjust the 2nd Parameter of the selected Pads page 29 PADSFunctionality depends on the selected Pads page.
See further details in VirtualDJ Manual - Pads Functionality depends on the selected Pads page.
See further details in VirtualDJ Manual - Pads
REAR PANEL - CONNECTIONS 2 x Denon SC6000 + Mixer Connections Denon SC6000 - Rear panel
30 LINE OUT - LAYER AUse standard RCA cables to connect this output to your DJ mixer and send out the audio signal from Layer A. Denon This output is used only in Standalone mode.31 LINE OUT - LAYER BUse standard RCA cables to connect this output to your DJ mixer and send out the audio signal from Layer B. This output is used only in Standalone mode.32 DIGITAL OUTUse standard digital coaxial cables to connect these 24-bit/96 KHz outputs to devices and mixers such as the Denon DJ X1800/X1850 Prime mixers.33 REMOTEUse a standard remote start cable to connect this input to the remote-start output of your mixer (if available). While connected to a remote-start-compatible mixer, moving the crossfader toward the side that corresponds to this SC6000 Prime (or raising the channel fader for its channel) will automatically start the track on the currently selected layer.34 USB HUB Connect standard USB drives to these USB ports. When you select one of those USB drives as a source (press the Source button), you can use the display to select and load tracks on your USB drives. There is also a similar USB port on the front panel.
Note that devices connected to these ports will not be available as Computer devices, if the SC6000 is in Standalone mode35 USBUse the provided USB cable (included) to connect this USB port to an available USB port on your computer. This connection sends and receives MIDI messages to and from the computer when the SC6000 is set to Computer mode 36 LINKUse the included networking cable to connect this port to another SC6000 Prime or to your Denon DJ X1800/X1850 Prime mixer. Each networked SC6000 Prime can share track databases, timing and BPM information, and other track data over this connection.
This connection is not used in Computer mode.37 POWER BUTTONPress this button to power SC6000 Prime on or off. Power on SC6000 Prime only after you have connected all of your input devices and before you power on your amplifiers and loudspeakers. Power off your amplifiers and loudspeakers before powering off SC6000 Prime.
Press and hold this button for 10 seconds to reset SC6000 Prime. 38 POWER INPUT Use the included power cable to connect this input to a power outlet. SC6000 Prime has a protection circuit to keep it powered on for 10 seconds after an unexpected power loss. Within 10 seconds after losing power (you will see a message in the display), reconnect it to your power source to return to normal operation.
SC6000 has a fully functional and customize-able 10" touch-screen offering all the information needed for your mix. The default UI for the screen will be automatically downloaded the first time you connect the SC6000 to a computer running VirtualDJ (Internet connection is required at least for the 1st time)
The default UI of SC6000 offers 3 main views:
- Full Deck
View (default) with Deck information, including Pads and Sampler panels.
- Basic Deck
View , with Basic Deck information (without Pads and Sampler), and a small Browser view
- Full Browser
view with Midi Deck..
Use the SHORTCUTS
button on the SC6000 to toggle between the Full and Basic Deck views.
Use the VIEW
button to toggle between Deck and Browser views. Denon SC6000 Screen - Full Deck view Denon SC6000 Screen - Basic Deck view Denon SC6000 Screen - Browser View 1Indicates the Deck that the device is controlling. Tap to switch to a different Deck2Track's Title, Remix and Artist. Tap this area to see other Track's info such as Album, Year, Genre and Comment.3Track's Length, original BPM and Key. Tap Key value to toggle between Musical and Camelot value.4Track's progress wave with Hotcues markers. Can be locked from Settings to prevent accidental taps5Track's musical key information. Key value can be displayed in Harmonic or Camelot view. Line is colored based on the key value. The MATCH text will be highlighted when Track's key matches the key of the other Deck.
Tap this area to get more key controls at the Deck info area.6Current Loop size in beats. 7Track's Time. Tap this area to toggle between Elapsed and Remain Time.8Track's Tempo information : Current BPM, Pitch, Pitch range%
Tap the BPM value area to to get Beat-grid Adjust controls at the Deck Info area.9Quantize. Tap to enable/disable.10Automix. Tap to enable/disable Automix on this deck.11Master Deck indicator12Beat-grid information in Bars : Beats13Wave Zoom mode. Tap to enable (icon will blink) and then use the BROWSE encoder to zoom the waveform in/out. Tap again to disable the Zoom mode.14Waveform.Can be locked (from accidental touch) or displayed in different colors and types, depending on the settings that can be found in the WAVES tab of SETTINGS view15Performance Pads. Displays the name of the currently selected Pads page, the values of its Parameters (if available) and information about the Pads functionality of the selected page.16Show/hide Sampler Bank and Sampler mode controls.17Show/hide Custom Buttons panel 18Select to view the Folders List.19Select to view the Songs List.20Select to view the Sideview. Tap again to cycle through the available lists of Sideview (Automix, Sidelist, Karaoke, Sampler and Shortcuts.21Browser Info. Tap to show/hide Info panel on the right side of the Browser for the browsed track. See VirtualDJ Manual on how to customize what this panel will display22Text Options. Tap to show/hide buttons to enlarge/reduce the Font size and 3 levels of Line padding23Tap to get the On-Screen Keyboard and search for tracks in your Library
down the [VIEW]
button for more than 2 seconds to get the SETTINGS view. Press the VIEW button again to go back to the Decks view.
Various settings are offered to adjust views, Waves, Browser behavior etc. and their values will be kept across sessions. A description of each setting is displayed at the bottom of the view, each time you tap, select or change a setting. Denon SC6000 screen - Settings view
For further Technical features and specifications, visit Denon DJ SC6000 Prime
Hardware Integration Department 2020 - ATOMIX PRODUCTIONS Reproduction of this manual in full or in part without written permission from Atomix Productions is prohibited.