Forum: VirtualDJ Technical Support
(NOTE: VirtualDJ continuously updated, so many older topic on this forum are most probably already fixed in the current build)
If you need extended support, contact our Support Team.
Forum Guidelines (*) The moderators hold the rights to remove, move or modify posts.
Sujet Samler output crackles... - Page: 1
This was rock solid before 8.2
Posté Tue 07 Jun 16 @ 7:13 am
The sample is set to Sync-Lock, and pitchQuality is set to 2?
Posté Tue 07 Jun 16 @ 10:37 am
It's completely un-usable for me. Sorry but I have to go back to 2857 when this worked *without any issue*
The crackles shows up most in low-frequency contents like a drum loop.
EDIT: Installed 2857 and sampler works perfect again.
Posté Tue 07 Jun 16 @ 6:05 pm
Posté Wed 08 Jun 16 @ 10:29 am
Posté Wed 08 Jun 16 @ 11:02 am
And with everything else thrown on the sampler.
It sounds like clipping, just like the headroom was lower. Did this change while upgrading the audio engine ?
While playing a sample and writing a "?" in the browser search field, VDJ just restarted without notification, but that's another story... (maybe you have a log, I was online)
Doesn't the sampler output be affected by the "Zero dB" setting ?
Posté Wed 08 Jun 16 @ 5:23 pm
If it would be clipping, you could try if it makes a difference if you lowered the volume of the sample.
It wouldn't explain why it would only happen to synced samples though.
I assume the distortion is not happening when no decks are playing then?
Posté Wed 08 Jun 16 @ 6:24 pm
I can get distortion every time I try to match a sample with something thats either to fast or to slow.
The keylock gets super stressed and I can hear pops and clicks in the sample.
Posté Wed 08 Jun 16 @ 6:55 pm
2. Sample BPM has no impact.
3. It looks to me it's an issue with sampler output level. If reduced gain - no crackles / pops
4. The crackles appear even if a deck is not playing , but gets worse when a deck is playing , like "total" output level dependent
I will try to record it
Posté Wed 08 Jun 16 @ 7:10 pm
I can get the same problem if playing two decks at Zero dB -3dB and boost LOW EQ or GAIN turned up.
My conclusion is that the limiter does not kick in before digital clipping occours.
So to sum up, this is not entirely related to sampler but for some reason the sampler showed this problem more evident than decks.
I have again verified that build 2857 does not have this problem and it has not.
Could I just have an answer why the sampler output is not affected by Zero dB setpoint ?
Latest finding: (EDIT)
Crackles only occour with WASAPI drivers and not Denon ASIO
Posté Wed 08 Jun 16 @ 7:34 pm
Posté Thu 09 Jun 16 @ 7:33 pm
Posté Fri 10 Jun 16 @ 9:05 am
Posté Fri 10 Jun 16 @ 9:37 am
What does that tell ?
Posté Fri 10 Jun 16 @ 4:22 pm
If it only happens with wasapi, there's some things that you can try:
-See what 'exclusiveAudioAccess' is set to. If it's set to yes, it means that either the device is not good for exclusive audio access or that the selected latency is too low.
Check on the Audio tab what the current latency is in samples (by hovering the mouse over the sound card name), then try to increase it by manually setting the 'latency' option.
If that doesn't work, try setting exclusiveAudioAccess to no.
-If it's already at no, it should be fine for most devices, but you could try if you get better results setting it to yes.
Posté Fri 10 Jun 16 @ 4:28 pm
Been running both Denon ASIO and WASAPI without any problem.
Also, build 2857 does not have this problem.
Setting exclusive option to no makes VDJ fail to initialize the connected MC6000 mk1. It must be set to yes to operate.
Latency is 576 samples (12.0 ms at 48kHz)
Those settings is exactly the same as in 2857 and does not cause problems. Latency exactly the same.
Posté Fri 10 Jun 16 @ 4:55 pm
The only change I can think of is that exclusive mode is better supported, so it's possible that 2857 connected in shared mode even when exclusiveAudioAccess was set to yes.
(To check if that was the case, check the end of the audio line in 2857 to see what it says exactly)
Posté Fri 10 Jun 16 @ 5:02 pm
I don't fully understand "(To check if that was the case, check the end of the audio line in 2857 to see what it says exactly)" ?
Posté Fri 10 Jun 16 @ 5:07 pm
Posté Fri 10 Jun 16 @ 5:17 pm
Posté Fri 10 Jun 16 @ 5:55 pm