Hardware Manuals


Reloop - Beatmix 2 - Disposition  

Pads


Pads (14) offer 3 different modes, depending on the PAD MODE buttons (15). Press PAD MODE button A to receive the HotCues-Loop mode. Press the PAD MODE button B to receive the Sampler mode. Press both PAD MODE buttons A and B at the same time (both Leds will be on) to receive the HotCues-Sampler mode



HotCues-Loop mode


Press the PAD MODE button A to set the PADs to Hotcues-Loop mode.


HotCues-Loop mode


HotCues-Loop mode when SHIFT is held


Each one of the 4 top pads assigns a Hot Cue Point (1 to 4) or returns the track to that Hot Cue Point.
When a Hot Cue Button is unlit, you can assign a Hot Cue Point by pressing it at the desired point in your track. Once it is assigned, the Hot Cue Button will light up blue.
Hold SHIFT down and then press one of the 4 top pads to delete its assigned Hot Cue Point.

Each one of the 4 bottom pads triggers a loop of a different size (in beats), as per the image.
Hold SHIFT and then use the 4 bottom pads to set and trigger a manual loop.
Pad Nr.5 is assigned as a smart loop button. Press the pad to set a Loop In (Entry) point. Press the same pad again to set a Loop Out (Exit) point and trigger the manual loop. Press once again to exit the loop.
Use Pads Nr.6 and 7 to half and double the size of the Loop.
Use Pad Nr.8 to trigger the last used Loop (reloop)

Sampler mode


Press the PAD MODE button B to set the PADs to Sampler mode.


Sampler mode


Sampler mode when SHIFT is held


Each one of the 8 pads triggers a sample slot from the selected Sampler Bank of VirtualDJ. If a bank has less than 9 samples, both sides of the Beatmix 2 will control the same samples. If a bank has more than 8 samples, the left side of the Beatmix 2 will control samples 1 to 8 and the right side samples 9 to 16. The Leds of the pads will be on if a sampler slot is loaded and will blink if plays.

Hold SHIFT down to receive additional parameters of the Sampler.
Use Pads 1 to 4 to select the 4 first (default) banks of VirtualDJ Sampler
Use Pads 4 to 8 to select the sampler trigger mode (On/off, Hold, Stutter and Unmute)

HotCues-Sampler mode


Press both the PAD MODE buttons A and B to set the PADs to HotCues-Sampler mode.


HotCues-Sampler mode


HotCues-Sampler mode when SHIFT is held

Each one of the 4 top pads assigns a Hot Cue Point (1 to 4) or returns the track to that Hot Cue Point.
When a Hot Cue Button is unlit, you can assign a Hot Cue Point by pressing it at the desired point in your track. Once it is assigned, the Hot Cue Button will light up blue.
Hold SHIFT down and then press one of the 4 top pads to delete its assigned Hot Cue Point.

Each one of the 4 bottom pads triggers a sample slot from the selected Sampler Bank of VirtualDJ. If a bank has less than 9 samples, both sides of the Beatmix 2 will control the same samples. If a bank has more than 8 samples, the left side of the Beatmix 2 will control samples 1 to 4 and the right side samples 9 to 12. The Leds of the pads will be on if a sampler slot is loaded and will blink if plays.
Hold SHIFT down and use the bottom Pads to select the 4 first (default) banks of VirtualDJ Sampler

Mixeur & Navigateur